 |
Funnels,
Standard and Custom:
Order funnels that are in stock at all times with sizes ranging
from a 1" opening to a 7" opening. Custom funnels
are also provided to facilitate loading. Having the proper
funnel and bag size for your product is very crucial to an
efficient operation. |
 |
AF-10
Accumulating Funnel:
Pneumatic gate increases the speed of automatic operations
by "staging" the product immediately above the bag
opening. When the bag is ready to receive the product, the
gate opens, enters the bag, and maintains the bag opening
to reduce product spills.
|
 |
CF-10
Counting Funnel:
Add a photo array to the AF-10 funnel for inline bagging operations.
Counts product as it enters the funnel; pneumatic funnel causes
separation between counts for continuous feed operations. |
 |
LS-10
Load / Support Shelf:
Supports the bottom/back of bag during loading of heavier
or bulkier products. Pneumatically operated, adjustable shelf
provides support and takes the initial impact of heavier products
dropping into the bag. Shelf tilts downward after sealing,
dropping product from the shelf. Available in various length
for longer bag sizes.
LSV-10
Vibratory Shelf Attachment:
"Taps" the bag to settle product to the bottom of
the bag. Pneumatic operation with speed controls. LS-10 Option
must be previously installed or purchased with the vibratory
shelf attachment. |
 |
LC-10
Light Safety Curtain:
An OSHA approved safety device that restricts the cycle operation
of the bagger when the optical detection field is obstructed.
LC-10 option is recommended when the funnel is removed and
the product is loaded directly into the bag. Increase production
by 40% by turning on the "auto" feature to cycle
the bagger on the trailing edge of the light curtain input
signal. Lockout key is provided to prohibit bypassing the
safety feature. Excellent option for hand loading operations. |
 |
DF-10
Diverting Funnel/Bag Counting Option:
As finished bags are sealed and dropped from your bagger,
they can be counted and redirected at the end of each preset
count. With a two box system, the bags are directed into "Box
A" until the final count is reached. Then the diverter
rotates, directing the bags into "Box B" allowing
the operator time to remove, seal and replace "Box A".
Includes diverting/rotating attachment, photo array, brackets
and counter controls. (UF-2000 Incline Conveyor sold separately.) |
 |
PT-10
Partition Table Attachment:
Stainless steel partitioned utility table keeps products separated
for manual kit packaging. Two sizes available depending upon
size and quantity of product. Adjustable tilt and height to
fit over bagger |
 |
LB-10
Label Applicator Attachment:
Apply preprinted labels inline while bagging. Labels are accurately
dispensed onto the bag from an air vacuum grid with +/- 1/32"
dispensing accuracy. Also Print and Apply labels with our
thermal transfer printer/label applicator. Print up to 305dpi
on labels from 1/2" x 1/2" up to 4" x 6". |
 |
CD-10
Compact Disc Loader:
With the CD Loader option, the T-1000 packages compact discs
at a rate of up to 70 packages per minute. Package into tamper
evident poly bags, either printed or nonprinted Significantly
reduce packaging costs over jewel cases or sleeves. |
 |
PB-20
Dual Optical Palm Buttons:
OSHA approved safety device. Two optical "no-touch"
buttons must be pressed simultaneously to initiate the cycle
operation of the bagger. If the two sensors are not pressed
at the same time, the bagger will not cycle, ensuring that
fingers or hands cannot be in the seal area. Recommended when
no funnel is present. |
 |
SP-10
Level 1 Spare Parts Kit:
Kit contains day to day normal wear items. Teflon, filter,
fuses, seal rubber, and heater cartridges identifies some
items in the kit.
SP-20
Level 2 Spare Parts Kit:
Additional items not projected to fail, but due to the cost
of loss of production, are required to prevent downtime. Valves,
cylinders, circuit boards, and a touch screen are some of
items included in this kit. |
 |
FS-10
Flat Seal Assembly:
Decreases the possibility of wrinkles in the seal area while
increasing seal integrity. Pneumatically operated opposing
"fingers" pull each side of the bag taught above
the seal area to flatten the seal area. |
 |
BF-10
Bag Deflator:
Removes excess air from the bag. Sponge or rubber loop deflators
push the air out just prior to sealing. |
 |
BV-10
Barcode Verifier:
Verifies that barcodes on preprinted or thermally printed
bags are readable and stops the cycle operation when a non-readable
barcode is detected. |
More
Options
AD-10
Point of Use Air Dryer:
Filter 99% of liquids from your plant air with this dryer
component. Liquids are then automatically drained before
entering the pneumatic system increasing component life.
BO-10
Bag "Out" Sensor:
Detects the last bag off the roll and shuts down the bagger,
while alerting the operator of the fault condition.
BO-20
Bag "Open" Sensor:
(AF-10 Funnel required.) Detects whether the bag has properly
blown open prior to the product entering the bag.
CB-10
Compartment Seal Option:
Separate two products in one bag by creating a seal between
two compartments. After the first product is loaded, press
the foot switch to seal the first product in the bag. Then
load the second product, and press the foot switch to index
the bag and seal the bag a second time above the second
product. The bag is then detached and another bag is indexed
into the loading position.
FD-10
Single 3-1/2" Floppy Disk Loader:
With the Floppy Disk Loader option, the T-1000 packages
3-1/2" floppy disks at a rate of up to 60 packages per minute.
- Cartridge
tray holds up to 300 floppy disks.
- Load
floppy disks while bagging.
- Loader
can be quickly removed to package manuals, case drivers,
instruction sheets or any other loose items such as screws,
keys or kits.
IF-10
Insert Funnel:
For products affected by air flow, an insert funnel provides
a solution. After the bag has been blown open, the funnel
enters the bag, holding it open so air can be decreased or
shut off. The funnel enters past the seal area decreasing
the potential of seal contamination. This is good for granular
type products.
OFS-10
Output Fault Signal:
Signal is provided to advise third party equipment that a
fault condition (i.e.: out of bags, jam detection, printer
error) is present on the T-1000 bagger and to cease production
operations. Audible or visual signals can also be provided
to alert the operator.
QC-10
Quick Roll Change Option:
Additional roll shaft and roll chucks. By having a full roll
shafted, the operator can perform roll changes quickly and
immediately when the bagger is out of bags.
TS-10
Trim Seal Assembly:
Trims excess film from bag above seal to enhance the appearance
of the package (retail products).
TW-10
Twin-Seal Option:
Automatically seals the bag a second time, 3/4" from the first
seal to increase bag integrity.
VA-10
Vacuum Bag Opening Assembly:
When air flow is not sufficient to open the bag, or when air
cannot be used to open the bag, vacuum tips do the job. Tips
protrude to the bag and retract pulling the bag open. Air
flow can be shut off for products affected by air flow. |
